哈嘍，大家好，“博皓復材課堂”欄目又和大家見面了，今天小編想跟各位小主探討的是一個復合材料行業老生常談的話題，那就是新模具為什么會容易粘模。算是把冷菜熱一下，再端給各位小主品嘗品嘗。各位小主不喜勿噴?。?/span>
話說1988-1989年間，美國玻璃纖維制造協會在進行工裝和模具制造研討會時，進行了一項有關模具粘模問題的調查。這項調查由524名從事玻璃鋼模具工具操作的人完成。
Question: Have you ever stuck a mold on a plug?
Response: Almost 15% reported they had stuck a mold on a plug, at least one time.
問題：是否經歷過模具被卡住脫不了模?
回答：近15%的人說他們至少有一次模具被卡住。
Question: Have you ever stuck a part in a new mold?
Response: Over 90% reported they had stuck parts in a new mold, at least one time.
問題：是否在新模具中遇到部件粘模問題?
回答：超過90%的人至少有一次在新模具上遇到部件粘模問題。
Question: Of all the molds you’ve built, how many have stuck one of the first three molded parts?
Response: About 13-15% of all initial parts stick in new molds.
問題：在你制作的所有模具中，前三個模制品有多少比例會粘到模具上？
回答：大約有13-15%的初始部位會粘在新模具上。
Question: What brand and type of mold release had been used on the molds that stuck?
Response:The brand and types of release agents were evenly distributed according to market share. All major mold release brands were reported to stick 13-15%(+/-1%) of new molds.
問題：粘模的時候，模具上使用了什么品牌和類型的脫模劑?
回答：根據市場份額，各種品牌和發行代理商都有粘模具情況。據報道，主要的脫模劑品牌有13-15%(+/-1%)的比例在新模具上會產生粘模問題。
The Smokeless Gun
One of the presuppositions of the survey was that certain types of mold releases would perform better than others. In closely examining the data it was found that 13-15% of ALL new molds stick, regardless of the type or brand of mold release used. All of the mold release types were reported to stick approximately the same number of new molds (within +/-1% of each other). The conclusion is that the type of mold release has very little bearing on mold sticking.
翻譯：該調查的前提之一是，某些類型的脫模劑會比其他類型的產品性能更好。在仔細檢查調查數據時發現，無論使用哪種類型或品牌的脫模劑，所有新模具都有13-15%的粘模幾率。所有脫模劑類型都有相同的粘模概率 (誤差在+/-1%之間)。結論是，脫模劑類型對模具的粘接影響很小。
以上是關于粘模的調查結果， 各位小主如果對調查結果有什么疑問，敬請?jiān)谖恼孪路搅粞耘叮?/span>
還有知道了新模具的確容易粘模，那么為什么會粘模呢？如何解決這類問題呢？
在下一篇文章里，小編將與各位一起一探究竟！
是不是很期待呢，請多關注博皓微信公眾號，趕緊來搶沙發吧！
特別聲明，本文章由博皓小編采集資料編輯（來自Boh.Lacovava）。
如想轉載請注明轉自廣東博皓復合材料有限公司微信公眾號。
打印
